How to Drill Pilot Holes and Drive Screws Without Splitting the Wood
By Mark Ellis | Updated November 2026
Screws are one of the quickest ways to join wood, and one of the easiest ways to ruin a nice board. A screw driven without a pilot hole can split the end of a board, a screw head can tear the surface, and a joint can stay loose even though the screw feels tight. The good news is that almost all of these problems come from a few simple things: the wrong screw, the wrong hole, or the wrong technique. This guide explains how wood screws work, how to choose a screw, how to size pilot and clearance holes, when to countersink or counterbore, and how to drive screws cleanly with a drill or driver.
At a glance: screwing wood without splitting it
| Question | Short answer |
|---|---|
| Do I need a pilot hole? | Almost always in hardwood, near the end or edge of a board, and with screws larger than about #6 |
| How big should the pilot hole be? | About the size of the screw's core (the solid shaft inside the threads), a little smaller in softwood |
| What's a clearance hole? | A hole in the top board as wide as the screw's shank, so the screw pulls the boards together |
| How long should the screw be? | Long enough that roughly half to two-thirds of its length goes into the bottom board |
| How far from the end of a board? | Keep screws back from ends and edges where you can; drill a pilot hole whenever you can't |
| Drill or impact driver? | A drill/driver with a clutch is easier to control for fine work; an impact driver is great for long screws |
| How do I stop cam-out? | Use the right bit size and type, push firmly, and keep the driver in line with the screw |
| Screws or glue? | Often both: glue for strength along long grain, screws for clamping, alignment and end grain |
How a wood screw holds
A wood screw works by its threads cutting a spiral groove into the wood and gripping the fibres. The holding power comes mostly from the bottom board, the one the threads bite into. For a screw to pull two boards tightly together, the threads should grip only the bottom board, while the top board lets the screw slide through. That's why a lot of screws have a smooth, unthreaded section under the head, and why woodworkers drill a slightly bigger hole through the top board.
When a screw is forced into wood with no hole at all, it has to push the fibres aside. In soft, forgiving wood away from the ends that's often fine. In hard, dense wood, or near the end of a board where there's little wood to resist, those fibres wedge apart and the board splits along the grain.
Choosing the right screw
| Screw type | Best for | Notes |
|---|---|---|
| General wood screws | Furniture, boxes, shelves, jigs | Many have a smooth shank; the most common choice indoors |
| Self-drilling or "cutting tip" wood screws | Quick general work, softwoods | A notched tip cuts its own path; still benefits from a pilot hole near ends |
| Pocket-hole screws | Pocket-hole joints | Flat washer head; use fine thread for hardwood and coarse thread for softwood and plywood |
| Deck and exterior screws | Outdoor projects | Coated or stainless for corrosion resistance; use stainless with cedar and treated lumber where the maker recommends it |
| Drywall screws | Drywall, not furniture | Brittle and prone to snapping; best avoided for woodworking joints |
| Construction or structural screws | Framing and load-bearing work | Only where a rated screw is specified; follow the maker's guidance |
A few things to check on the box:
- Gauge (thickness). Wood screws are often sold by gauge in North America, such as #6, #8 and #10; metric screws are sold by diameter in millimetres. A #8 is a sensible all-rounder for furniture and shelves.
- Length. As a rule of thumb, choose a screw long enough that about half to two-thirds of its length goes into the bottom board, without poking out of the far side.
- Head type. Flat (countersunk) heads sit flush with the surface; pan and washer heads sit on top and hold well in sheet goods and hardware.
- Drive type. Square (Robertson) and star (Torx) drives grip the bit much better than Phillips and are far less likely to strip, which makes a big difference for beginners.
- Thread. Coarse threads hold better in softwood, plywood and MDF; fine threads are less likely to split dense hardwood.
Pilot holes, clearance holes and countersinks explained
There are three different holes involved in a clean screwed joint. You won't always need all three, but it helps to know what each does.
- Pilot hole: a small hole in the bottom board for the threads. It gives the screw a path so it doesn't wedge the wood apart, and it keeps the screw going straight.
- Clearance hole: a hole in the top board, about as wide as the screw's smooth shank. The screw slides through it, so the head can pull the top board down tight against the bottom one instead of the threads holding the two boards apart.
- Countersink: a cone-shaped recess at the top of the hole so a flat-head screw sits flush or just below the surface. A counterbore is a deeper, flat-bottomed hole that sinks the whole head below the surface so you can cover it with a wooden plug.
Combination bits drill the pilot hole, clearance hole and countersink in one pass. They're worth buying for the screw sizes you use most.
Sizing pilot holes
The simplest way to choose a pilot bit is to hold it in front of the screw. The bit should hide the solid core of the screw while you can still see the threads sticking out on both sides. In softwood, go a little smaller than the core; in hardwood, match the core or go a hair bigger.
The chart below is a common starting point for standard wood screws. Screw makers' charts vary a little, so check the box when it has one, and always test on a scrap of the same wood.
| Screw gauge | Pilot bit, softwood | Pilot bit, hardwood | Clearance bit (top board) |
|---|---|---|---|
| #6 | 1/16" | 5/64" | 9/64" |
| #8 | 5/64" | 3/32" | 11/64" |
| #10 | 3/32" | 7/64" | 3/16" |
A few adjustments:
- Very dense woods such as oak, maple and hickory may need a slightly bigger pilot hole, and sometimes wax on the screw threads.
- Plywood usually takes the softwood size. Drill pilot holes into plywood edges, which split and delaminate easily.
- MDF and particleboard split at the edges if you skip the pilot hole. Use screws made for these materials when you can, and keep them well back from corners.
- Pilot depth: drill about as deep as the screw will go. A pilot hole that's too shallow leaves the tip of the screw to force its way in, which can still split the wood.
Step by step: driving a screw cleanly
- Mark the screw position. Measure and mark where the screw goes. Keep it away from the end of the board where you can; if you can't, the pilot hole matters even more. Our guide to measuring and marking wood covers accurate layout.
- Clamp the parts. Clamp the boards in their final position so they can't shift while you drill. If the joint is glued, apply glue first, then clamp and drill.
- Drill the clearance hole through the top board. Hold the drill square to the surface. A small square or a scrap block set beside the bit helps you keep it straight.
- Drill the pilot hole into the bottom board. Use the smaller bit to the depth of the screw. A piece of tape wrapped around the bit makes a simple depth stop.
- Countersink or counterbore if needed. Go just deep enough for the head to sit flush or slightly below the surface. Test on a scrap first, since it's easy to go too deep.
- Pick the right bit for the screw head. A bit that fits snugly in the recess is the single best way to avoid stripped heads.
- Drive the screw. Start slowly, push firmly in line with the screw, and let the threads do the work. Slow down as the head nears the surface.
- Stop when it's snug. The head should pull the boards together and seat flush. Overtightening strips the threads in the wood or snaps the screw. On a drill/driver, set the clutch so it slips just as the screw seats.
Drill/driver or impact driver?
| Tool | Best for | Things to know |
|---|---|---|
| Drill/driver | Drilling holes, driving small and medium screws, delicate work | The adjustable clutch stops at a set torque, which helps prevent overdriving and stripping |
| Impact driver | Long screws, dense wood, decks and framing | Very powerful and less tiring for long screws, but easy to overdrive small screws or snap brass ones |
| Hand screwdriver | Brass screws, hinges, hardware, final tightening | Slow, but gives the most feel and control |
If you only own one, a drill/driver handles most beginner projects. For brass screws, which are soft and snap easily, drive a steel screw of the same size into the hole first to cut the threads, then remove it and drive the brass screw by hand.
Screwing near the end of a board
Ends and edges are where most splits happen, because the wood has nowhere to go. To keep the risk down:
- Drill a pilot hole every time near the end of a board, even in softwood.
- Keep screws back from the end and edge where the design allows. A common habit is to stay at least an inch from the end of a board where you can.
- Stagger screws along a board instead of lining them up in a row on the same grain line, which can split along that line.
- Use a smaller gauge screw in thin or narrow stock.
- Screws driven straight into end grain hold poorly. If you must screw into end grain, use a longer screw, or drill a hole across the board and glue in a hardwood dowel for the threads to bite into. Our guide to basic wood joints shows stronger alternatives.
Screws and glue together
Screws and glue do different jobs. On long-grain joints, glue usually provides most of the strength, and the screws act like built-in clamps that hold the joint closed while the glue dries. On end-grain joints, where glue is weak, the screws do more of the work. For many furniture projects, using both gives you a strong joint with no need for a large set of clamps. See How to Glue and Clamp Wood for choosing a glue and doing a clean glue-up.
Wipe away squeeze-out around the screw before it dries, especially if the piece will be stained, since dried glue blocks stain and finish.
Hiding screws
- Wood plugs: counterbore the hole, drive the screw, then glue in a matching plug and trim it flush. Line the plug's grain up with the board for the neatest look.
- Wood filler: fill shallow countersinks with filler and sand it flush. Filler often looks different once stained, so test first.
- Hide them from view: drive screws from the back, the underside, or inside a cabinet, or use pocket holes on faces that won't be seen.
Common problems and fixes
| Problem | Likely cause | Fix |
|---|---|---|
| Board splits | No pilot hole, pilot too small or shallow, screw too close to the end | Drill a correctly sized pilot to full depth; move the screw back from the end; glue and clamp the split |
| Gap between boards | Threads gripping both boards | Drill a clearance hole through the top board; clamp before driving |
| Stripped screw head | Wrong or worn bit, not pushing hard enough, overdriving | Use a snug square or star bit; push in line; set the clutch lower; use a screw extractor on a stuck screw |
| Screw spins and won't tighten | Hole stripped in the wood, pilot too big | Move the screw slightly, use a longer or thicker screw, or glue wooden toothpicks or a dowel into the hole and redrill |
| Screw snaps | Dense wood with no pilot, soft screw (brass or drywall), too much torque | Drill a bigger pilot; wax the threads; use a better screw; drive by hand at the end |
| Screw goes in crooked | Drill not held square, no pilot hole | Use a square or drill guide when drilling; start the screw slowly |
| Head sits proud | Countersink too shallow | Deepen the countersink slightly and drive again |
| Head sinks too deep or tears the surface | Overdriving, especially with an impact driver | Set the clutch; slow down as the head nears the surface; use a countersink for flat heads |
| Screw pokes through the far side | Screw too long | Measure both boards before choosing a screw; aim for half to two-thirds into the bottom board |
Safety notes
Wear safety glasses when drilling and driving, because bits can snap and chips fly. Clamp small parts instead of holding them by hand, and keep your hand out of line with the bit in case it slips. Unplug corded drills or remove the battery before changing bits. Long hair, loose sleeves and gloves can catch in a spinning drill, so tie them back or take them off. Check for hidden wires and pipes before drilling into walls. For more, see Woodworking Safety Basics.
Frequently asked questions
Do I really need a pilot hole for every screw? Not always. In softwood, away from the ends, a small self-drilling screw often goes in fine without one. In hardwood, near ends and edges, in plywood edges, and for larger screws, a pilot hole prevents splits and keeps screws straight.
What size drill bit for a #8 screw? A common starting point is a 5/64" pilot bit in softwood and 3/32" in hardwood, with an 11/64" clearance hole in the top board. Check the screw maker's chart if there is one and test on scrap.
Why do my screws strip so easily? Usually the bit is the wrong size or worn, or the driver isn't held firmly in line with the screw. Switching to square or star drive screws solves most stripping problems.
Can I use drywall screws for woodworking? They'll work for jigs and shop fixtures, but they're brittle and can snap under load. For furniture, use proper wood screws.
How do I remove a stripped screw? Try a wide rubber band between the bit and the head for extra grip, or use an inexpensive screw extractor bit. If the head is gone, drill around it with a plug cutter or hollow drill, remove the plug, and glue in a new one.
Where to go next
Once you can drive a screw cleanly, a lot of projects open up. Try a simple box or wall shelf from Best First Woodworking Projects for Beginners, choose your boards with Choosing Wood for Beginner Projects, and check which tools you still need in Essential Hand Tools for a Small Home Workshop. When you want a bigger library of project ideas, our woodworking plans review looks at one paid plan collection alongside free alternatives.