How to Sand Wood: Grits, Sanding Order and Techniques for a Smooth Finish
By Mark Ellis | Updated October 2026
Sanding is the job most beginners rush, and it shows the moment finish goes on: stain turns every stray scratch into a dark line. Good sanding isn't about elbow grease. It's about the right grits in the right order, a few simple techniques, and knowing when to stop. This guide covers sandpaper grits and abrasive types, hand and power sanding, a sanding sequence that works, tricky spots like end grain, sanding between coats, and fixes for the problems everyone runs into.
At a glance: sanding basics
| Question | Short answer |
|---|---|
| Where do I start? | 80 grit for rough or marked wood, 120 for smooth planed or store-bought boards |
| Where do I stop before finishing? | Usually 180 or 220 grit |
| Can I skip grits? | Skip one at most; jumping from 80 to 220 leaves deep scratches behind |
| Which direction? | With the grain, especially for the final grit |
| How do I know a grit is done? | Pencil squiggles are gone and the scratches look even |
| Between finish coats? | A light scuff with 320–400 grit, then remove the dust |
| Most useful power sander? | A random orbit sander |
| What protection? | Eye protection and a dust mask or respirator; hearing protection for power sanders |
How sandpaper grits work
The grit number tells you how fine the abrasive particles are. Lower numbers are coarser and remove wood fast but leave deeper scratches. Higher numbers are finer and leave shallower scratches but remove wood slowly. Sanding just swaps big scratches for smaller ones until they're too fine to see.
| Grit range | Grade | Typical use |
|---|---|---|
| 40–60 | Coarse | Heavy stock removal, stripping old finish, flattening rough or uneven boards |
| 80–100 | Medium | Removing saw and planer marks, pencil marks, light shaping, levelling glue lines |
| 120–150 | Fine | General smoothing after medium grits; starting point for clean, planed wood |
| 180–220 | Very fine | Final sanding before stain, oil or clear finish |
| 320–400 | Extra fine | Light sanding between coats of finish |
| 600 and up | Ultra fine | Polishing a cured finish, usually wet-sanding with wet/dry paper |
Most beginner projects only need four grits: 80, 120, 180 and 220, plus some 320 for between coats.
Types of abrasives
The mineral on the paper matters almost as much as the grit. Here are the four you'll see most often.
- Aluminum oxide. The everyday choice for wood, usually tan, brown or red. It's tough and works well by hand and on power sanders. If you buy only one type, buy this.
- Garnet. A natural mineral, usually orange-red. It's softer and wears out faster, but it leaves a fine, even scratch on bare wood. Many woodworkers like it for hand sanding before finishing. It isn't a good fit for power sanders, where it dulls quickly.
- Silicon carbide. Very hard and sharp, usually dark grey or black. It's the mineral on most "wet/dry" paper and is popular for sanding between finish coats and for wet-sanding cured finishes, because it cuts finish cleanly.
- Ceramic. The toughest of the group, made for aggressive work: coarse grits, belt sanders and heavy stock removal. It's more than most beginners need.
For finishes and resinous softwoods like pine, look for open-coat or stearated (anti-clog) paper.
Hand sanding vs sanding block vs power sanders
| Method | Best for | Pros | Cons |
|---|---|---|---|
| Hand sanding (paper in your hand) | Curves, edges, mouldings, light touch-ups | Cheap, total control, follows shapes | Fingers press unevenly and create dips; slow on large areas |
| Sanding block | Flat surfaces, edges, small projects | Keeps surfaces flat, cheap, quiet, no dust cloud | Slow for big panels; tiring on lots of parts |
| Random orbit sander | Tabletops, panels, most flat work | Fast, leaves few visible marks, works in any direction | Can round edges; swirls if pushed or rushed; noisy and dusty |
| Detail sander | Corners, tight spots, inside small boxes | Reaches where round pads can't | Slow; small pad can dig in; leaves its own pattern |
Sanding blocks are the most underrated tool in the shop. A cork or rubber block, or simply a flat scrap of wood with paper wrapped around it, spreads pressure evenly so you sand the high spots down instead of following every dip. Use a block on every flat surface you sand by hand.
Random orbit sanders spin and orbit at the same time, so the scratch pattern is random rather than in neat lines. If you're building a small tool kit, see Essential Hand Tools for a Small Home Workshop for what to buy first; a sanding block belongs on that list long before any power sander.
Using a random orbit sander well
- Start the sander on the wood, or just above it, and stop it before lifting off.
- Let the weight of the sander do the work. Pressing down causes swirls.
- Move slowly in overlapping passes, covering the whole surface evenly.
- Keep the pad flat.
- Connect dust collection. A shop vacuum on the dust port keeps the paper cutting and the air cleaner.
Sanding order: a progression that works
The golden rule is simple: each grit's only job is to remove the scratches from the grit before it. Skip too far and the deeper scratches survive, showing up later under the finish.
A reliable sequence for most projects:
- Start at 80 grit if the wood has saw marks, planer ripples, glue squeeze-out or deep pencil marks. Start at 120 if it's already smooth, as most store-bought boards are.
- Move to 120, sanding until the 80-grit scratches are gone.
- Move to 180, sanding until the 120-grit scratches are gone.
- Finish at 220 if you want, or stop at 180.
- Remove the dust between grits., so loose coarse grit can't cause stray scratches.
Skipping one grit (80 to 150, or 120 to 220) is fine if you sand a little longer. Skipping two or more is where trouble starts.
When to stop
For most finishes, 180 to 220 grit is the right place to stop. Going much finer on bare wood rarely makes a visible difference under a clear coat, and on some woods it can make the surface absorb stain less evenly. If you plan to stain, test your final grit on a scrap of the same board first. Our guide on how to finish wood covers that testing step and the finishes themselves.
Technique: sand with the grain
Scratches that run along the grain blend into the wood's natural lines. Scratches across the grain stand out, especially under stain. So:
- Hand sand with the grain, in long, straight strokes along the full length of the board.
- With a random orbit sander, direction matters less, but finish each grit with light passes along the grain.
- Where two boards meet at right angles, such as at a frame corner, sand the piece that runs underneath first, then sand the crossing piece carefully along its own grain.
The pencil-mark trick
This simple trick takes the guesswork out of "Am I done with this grit?"
- Before each grit, draw light, loose pencil squiggles across the whole surface.
- Sand until every mark is gone.
- When the marks disappear evenly, the surface has been sanded uniformly with that grit. Move to the next one and draw fresh squiggles.
If marks vanish in one area but not another, you've found a low spot, or you've been leaning on one side of the sander.
Raising the grain
When water touches sanded wood, crushed fibres swell and stand up, leaving the surface feeling fuzzy. Water-based stains and finishes do the same.
The fix is to raise the grain on purpose before finishing:
- After your final grit, wipe the surface with a damp (not soaking) cloth.
- Let it dry fully, usually an hour or two depending on conditions.
- Sand lightly with your final grit to knock off the raised fibres. A few light passes by hand with a block are enough.
This step matters most before water-based stains and finishes, and on anything that will get wet in use, like cutting boards or bathroom shelves.
Sanding end grain
End grain is the cut end of a board, where the fibres face outward like a bundle of straws. It's harder to sand smooth and it soaks up stain and finish much faster than the face, so ends often turn out darker than the rest of the piece.
- Sand end grain one or two grits finer than the faces (to 320, for example, if faces stop at 220). This closes up the surface a little and evens out absorption.
- Use a sanding block and keep it flat so the edges of the end don't get rounded.
- Test stain on a scrap end before committing.
Sanding between finish coats
Most film finishes, such as polyurethane, varnish and lacquer, benefit from a light sanding between coats. It smooths dust nibs and helps the next coat grip.
- Wait until the coat is fully dry, following the time on the can. Sanding a soft finish gums up the paper.
- Use 320–400 grit, silicon carbide or stearated aluminum oxide, on a soft block or a foam sanding pad.
- Sand lightly, just enough to turn the surface evenly dull. You're scuffing, not removing finish. Take extra care on edges, where it's easy to sand through.
- Remove all the dust with a vacuum and a tack cloth or a lint-free cloth, as the finish manufacturer recommends.
- Apply the next coat. Usually you don't sand the final coat unless you're polishing it.
If you sand through to bare wood, apply the next coat; the spot usually blends in. On stained work, touch up the colour first.
Dust control and safety
Sanding produces fine dust, and that's the part you most want to keep out of your eyes and lungs. A few habits make a big difference.
- Wear a dust mask or respirator rated for fine dust, and make sure it fits snugly. A loose paper mask does very little. Follow the manufacturer's guidance on fit and replacement.
- Wear eye protection. Power sanders throw dust and grit, and even hand sanding overhead can drop dust into your eyes.
- Wear hearing protection with power sanders, especially during longer sessions.
- Collect dust at the source. Hook a shop vacuum to your sander, sand outdoors or near an open door when you can, and clean up with a vacuum rather than a broom, which just puts fine dust back in the air.
- Keep your hands and cords clear of the pad, and unplug the sander before changing paper.
- Dispose of dust and rags properly. Rags used with oil finishes can heat up as they dry; lay them flat outdoors to dry or follow the instructions on the can.
For a fuller rundown of protective gear and shop habits, read Woodworking Safety Basics.
Common sanding problems and fixes
| Problem | Likely cause | Fix |
|---|---|---|
| Swirl marks (small loops) | Pressing down on a random orbit sander, moving too fast, or skipping grits | Go back one or two grits, let the sander's weight do the work, move slowly, finish with light passes along the grain |
| Scratches that show up under stain | Skipped grits, cross-grain sanding, or loose coarse grit left on the surface | Sand back with the grit that removes them, work through each grit, remove dust between grits; test stain on a scrap first |
| Rounded edges | Power sander hanging over the edge, or hand sanding without a block | Keep the pad fully on the surface near edges; use a block; ease edges by hand at the end |
| Dips or uneven surface | Sanding with fingers only, tilting the sander, or focusing on one spot | Use a flat block; keep the sander flat; use the pencil-mark trick to sand evenly |
| Clogged paper | Sanding resinous wood, soft finish, or glue; no dust collection | Use open-coat or stearated paper; let finishes dry fully; clean paper with an abrasive cleaning stick; use a vacuum |
| Fuzzy surface after finishing | Grain raised by water-based stain or finish | Raise the grain with a damp cloth before finishing, then sand lightly with your final grit |
| Dark, blotchy end grain | End grain absorbs more stain | Sand end grain finer, test on scrap, consider a sealer or wash coat first |
Frequently asked questions
What grit should I start with? It depends on the wood, not the project. Start at 80 for rough, marked or uneven wood, and at 120 for smooth, planed boards. Starting coarser than you need just creates deeper scratches you then have to remove.
Is 220 grit fine enough for a smooth finish? For most projects, yes. Sanding bare wood to 180 or 220 and then sanding lightly between coats gives a smooth result. The smoothness you feel at the end comes mostly from the finish and the between-coat sanding.
Can I reuse sandpaper? Yes, until it stops cutting. When the paper glides over the wood instead of producing fine dust, or it's clogged in spots, replace it.
How do I remove dust before finishing? Vacuum first, then wipe with a tack cloth or a cloth dampened as the finish maker recommends. Check by looking across the surface toward a light.
Where to go next
The best way to learn sanding is on a real project. A small box, cutting board or wall shelf gives you flat faces, edges and a bit of end grain to practise on. Pick one from Best First Woodworking Projects for Beginners, sand it through 80, 120, 180 and 220 using the pencil-mark trick, and then follow How to Finish Wood to bring out the grain. If you'd like a bigger library of project ideas once you're comfortable, our woodworking plans review looks at one paid plan collection alongside free alternatives.