How to Cut Wood Straight: Handsaw, Circular Saw and Jigsaw Basics for Beginners
By Mark Ellis | Updated November 2026
A lot of beginner woodworking frustration comes down to one thing: cuts that wander. A cut that drifts a little off the line leaves gaps in joints, wobbly legs and boxes that won't close square. The fix usually isn't a more expensive saw. It's choosing the right saw for the cut, supporting the wood properly, and using a few simple guides and habits. This guide covers the three saws most beginners start with (a handsaw, a circular saw and a jigsaw), how to set each one up, and how to get straight, square cuts safely.
At a glance: straight cuts for beginners
| Question | Short answer |
|---|---|
| Which saw should I buy first? | A good handsaw for small cuts; a circular saw if you'll be cutting plywood or longer boards |
| What's the biggest cause of crooked cuts? | Freehand cutting without a guide, plus wood that isn't supported or clamped |
| Which side of the line do I cut on? | The waste side, so the line stays on the piece you keep |
| What's a crosscut vs a rip cut? | A crosscut goes across the grain; a rip cut runs along the grain |
| How deep should a circular saw blade be? | About 1/4" (6 mm) below the bottom of the board |
| How do I stop splintering? | Use a fine-tooth blade, score the line, use painter's tape, and keep the good face where the teeth enter |
| Can a jigsaw cut straight? | It can with a guide and a sharp blade, but it's best for curves and short cuts |
| What matters most for safety? | Eye and hearing protection, clamped work, a supported offcut, and hands well clear of the blade |
Crosscuts and rip cuts
Before choosing a saw, it helps to know the two basic kinds of cut. A crosscut goes across the grain, like cutting a board to length. A rip cut runs along the grain, like cutting a wide board into narrower strips. Many saws and blades are tuned for one or the other. Crosscut teeth slice the fibres cleanly so the end isn't torn. Rip teeth act more like small chisels that clear wood quickly along the grain. General-purpose blades and saws do both reasonably well, which is what most beginners need.
Plywood and other sheet goods have grain running in different directions in each layer, so they behave more like crosscutting in every direction. A fine-tooth blade gives the cleanest edge on plywood.
Choosing a saw
| Saw | Best for | Strengths | Limits |
|---|---|---|---|
| Western handsaw (push stroke) | Cutting boards to length, occasional rip cuts | Cheap, quiet, no setup | Slower; takes practice to cut straight |
| Japanese pull saw | Fine crosscuts, joinery, small parts | Thin, clean cut, easy to start | Thin blade can buckle if forced |
| Circular saw | Cutting plywood and long boards, straight rips | Fast and accurate with a guide | Loud; needs good support and care |
| Jigsaw | Curves, cutouts, short cuts in thin stock | Versatile, easy to handle | Blade can flex and wander on long or thick cuts |
| Miter saw (later purchase) | Repeatable square and angled crosscuts | Very accurate for trim and frames | Limited cut width; larger investment |
If you're working on small projects in a small space, a pull saw and a square will take you a long way. If your projects involve plywood sheets or lots of boards, a circular saw with a straightedge guide is often the best value power tool you can own. A jigsaw is a useful second power saw for curves.
Before you cut: marking and support
Good cuts start before the saw touches the wood.
- Mark clearly. Use a sharp pencil or a marking knife and a square. For crosscuts, carry the line around at least two faces so you can check you're staying square. Our guide to measuring and marking explains this in more detail.
- Mark the waste. Put a small X on the offcut side of the line. It's easy to cut on the wrong side otherwise.
- Cut on the waste side. The saw blade removes a strip of wood called the kerf, usually around 1/8" (3 mm) for a circular saw blade and less for a handsaw. Keep the blade on the waste side so the line stays on your finished piece.
- Support both sides. If the offcut is unsupported, it will sag as you finish the cut. That pinches the blade, can make a circular saw kick back, and tears a splinter off the bottom edge. Support the board so neither side can drop or pinch.
- Clamp the work. A clamped board can't shift, and it leaves both your hands free to control the saw.
A simple way to support plywood for circular saw cuts is to lay a sheet of rigid foam insulation on the floor or on sawhorses, put the plywood on top, and set the blade to cut just into the foam. Both halves stay supported for the whole cut.
How to make a straight cut with a handsaw
- Clamp the board so the cut line overhangs the bench or sits between two supports.
- Start the cut carefully. Place the saw on the waste side of the line and rest the side of your thumb knuckle against the blade, well above the teeth, as a guide. Use a few short, light strokes (pull strokes for a Western saw, normal strokes for a pull saw) to make a small notch.
- Move your thumb away once the kerf is started, and lengthen your strokes.
- Line up your body. Stand so your arm, shoulder and the saw are in line with the cut, and you can see both the line and the side of the blade.
- Let the saw do the work. Use long, relaxed strokes with little downward pressure. Forcing the saw makes it wander and bind.
- Watch two lines. Keep an eye on the line on the top face and the line on the near edge so the cut stays square in both directions.
- Slow down at the end. Support the offcut with your free hand or a helper, and finish with light strokes so the last fibres don't tear.
A simple guide makes a big difference. Clamp a square block of scrap right against the line and keep the saw blade against it while you cut. This is a beginner's version of a saw guide and helps you stay both straight and square.
How to set up a circular saw
A circular saw can make very straight, accurate cuts, but setup matters.
- Use the right blade. A blade with around 24 teeth is fine for fast framing cuts. For plywood and furniture parts, a 40 to 60 tooth blade leaves a much cleaner edge.
- Set the depth. With the saw unplugged or the battery removed, set the blade so it extends about 1/4" (6 mm) below the bottom of the board. A shallow depth gives cleaner cuts and less kickback risk.
- Check the bevel is at 0°. Many saws drift slightly from true. Use a square against the blade and the base plate (avoiding the teeth) and adjust if needed.
- Know your blade's position. Most saws have a notch on the base plate showing where the blade cuts, but it isn't always accurate. Make a test cut in scrap and see where the kerf falls relative to the notch.
- Good face down. The teeth of a circular saw cut upward, so splinters tend to form on the top face. Put the face you want to look nice facing down.
Making a straight cut with a circular saw
The most reliable way to cut straight with a circular saw is to run it along a straightedge guide rather than following a pencil line by eye.
- Make or buy a guide. A simple shop-made guide is a strip of plywood about 12" wide with a straight factory-edged strip glued and screwed on top as a fence. Run the saw along the fence once to trim the base to exact width. From then on, the edge of the guide is exactly where the blade cuts. A long factory-straight board or a clamp-on aluminium straightedge also works.
- Line up the guide with the cut line, keeping the blade on the waste side, and clamp it at both ends.
- Support the work so the offcut can't drop and pinch the blade.
- Start the saw before it touches the wood. Let the blade reach full speed, then push it steadily forward with the base plate flat and the edge pressed lightly against the guide.
- Keep a steady feed rate. If the motor bogs down or you smell burning, slow down. Don't twist the saw to correct the line; that's what pinches the blade.
- Finish the cut and let the blade stop completely before lifting the saw. Wait for the guard to close.
For crosscuts on boards, a speed square makes a quick guide: hold its lip against the edge of the board and run the saw's base plate along the square's edge. Practise on scrap first, since the square needs to be held firmly.
Using a jigsaw
A jigsaw is the beginner's tool for curves and cutouts, and it can make short straight cuts too.
- Pick the right blade. Blades come for wood, metal and laminate, with different tooth counts. A fine-tooth blade gives a cleaner edge but cuts slower. Downcut or "clean cut" blades reduce splintering on the top face.
- Turn off orbital action for clean cuts. Many jigsaws have an orbital setting that swings the blade forward for faster cutting. It's great for rough cuts but leaves a rougher edge.
- Let the blade lead. Push gently and let the saw cut at its own pace. Pushing hard bends the blade, which makes the cut lean or wander.
- Cut curves in steps. For tight curves, make relief cuts from the edge to the line first, so waste pieces fall away as you go around the curve.
- For cutouts, drill a hole in the waste inside the line big enough for the blade, then start the cut from there.
- For straighter cuts, clamp a straightedge for the base plate to follow, just like a circular saw.
Preventing splintering and tear-out
Splintered edges are one of the most common beginner complaints, especially on plywood.
- Use a sharp, fine-tooth blade suited to the material.
- Score the cut line with a utility knife before cutting, so the surface fibres are already cut.
- Apply painter's tape along the line and mark on the tape.
- Put the good face where the teeth enter: face down for circular saws and most jigsaw blades, face up for a handsaw or table saw.
- Support the wood close to the cut so fibres can't break away.
- Slow down as you finish a cut, where tear-out is most likely.
Checking and cleaning up your cuts
After a cut, check it with a square across the face and across the edge. Small errors can be cleaned up with a block plane, a sanding block or a shooting board. Don't worry if your first cuts need trimming. Many experienced woodworkers cut slightly long on purpose and trim to the final line. Our guide to sanding wood covers smoothing edges once the cut is close.
Common problems and fixes
| Problem | Likely cause | Fix |
|---|---|---|
| Cut drifts off the line | Freehand cutting, forcing the saw, poor body position | Use a guide, ease off the pressure, stand in line with the cut |
| Cut isn't square to the face | Saw tilted during the cut | Watch the line on the edge as well as the face; use a guide block |
| Saw binds or kicks back | Offcut sagging and pinching the blade, twisting the saw | Support both sides, keep the saw straight, never force it |
| Splintered edges | Coarse or dull blade, wrong face up | Fine-tooth sharp blade, score or tape the line, good face where teeth enter |
| Burn marks | Dull blade or feeding too slowly | Clean or replace the blade; keep a steady feed rate |
| Parts end up too short | Cutting on the wrong side of the line | Mark the waste with an X and keep the blade on that side |
| Jigsaw cut leans | Blade bending from pushing too hard or a dull blade | Slow down, use a fresh blade, turn off orbital action |
Safety notes
Always wear safety glasses, and use hearing protection with power saws. Clamp the work instead of holding it, and keep both hands on the saw where the design allows. Never reach under the work while a circular saw is running, and stand slightly to one side of the cut line rather than directly behind the saw. Make sure the blade guard moves freely and closes properly. Unplug a corded saw or remove the battery before changing blades or adjusting depth. Keep cords out of the cutting path, and avoid loose sleeves, gloves near blades and dangling jewellery. Always follow the manufacturer's manual for your tool. For more, see Woodworking Safety Basics.
Frequently asked questions
What's the easiest saw for a beginner to cut straight with? A Japanese pull saw is easy to start and control for small crosscuts. For longer cuts and sheet goods, a circular saw run along a clamped straightedge is the easiest way to get a dead-straight cut.
Why does my circular saw cut wander even with a guide? Check that the guide is truly straight and clamped at both ends, that the saw's base plate stays pressed against it the whole way, and that the work is supported so it isn't flexing. A bent or dull blade can also pull the saw off course.
Do I need a table saw? No. Many furniture projects are made entirely with a circular saw, a jigsaw and hand tools. A table saw is a big investment and needs careful training to use safely.
How do I cut a large sheet of plywood alone? Lay it on rigid foam insulation on the floor or on sawhorses, set the blade just deep enough to cut into the foam, and use a clamped straightedge. Breaking big sheets into smaller pieces first makes them easier to handle.
How do I make several pieces exactly the same length? Cut one piece, check it, then use it or a stop block as a reference for the rest, rather than measuring each piece separately with a tape.
Where to go next
Once you can make clean, straight cuts, you can start joining parts together. Learn the main options in Basic Wood Joints for Beginners, see how to assemble parts in How to Glue and Clamp Wood and How to Drill Pilot Holes and Drive Screws, and pick a project from Best First Woodworking Projects for Beginners. Many plans include a cut list, so How to Read a Woodworking Plan and Cut List is worth a look too. When you want a bigger library of project ideas, our woodworking plans review looks at one paid plan collection alongside free alternatives.